Filter by Reset

All
Forums (172)
  • Other wireless (90)
  • Sub-1 GHz (72)
  • /etc... RF (Read-Only) (4)
  • MSP low-power microcontr... (3)
  • Zigbee & Thread (2)
  • Simulation, hardware & system... (1)
  • View all
Technical Articles (0)
Wikis (0)
Files (1)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 172 results View by: Thread Post Sort by

  • CC1020: Sensitivity issue in CC1020 Transceiver

    Part Number: CC1020 Tool/software: Hi everyone, I'm facing the same sensitivity issue that has been discussed in the community, but unfortunately, I haven't seen any responses or solutions yet. Issue: Sensitivity issue Details: even I got similar…
    • Answered

  • CC1200: Is it possible to receive the output of CC1020 with CC1200?

    Resolved
    Part Number: CC1200 Other Parts Discussed in Thread: CC1020 , Tool/software: Hi All, ・The output band of CC1020 is 426MHz. ・BPS (H, L) is controlled by entering H and L into DIO. H=3.3ms, L=1.68ms Is it possible to receive the output of CC1020 with CC1200…
    • Resolved

  • RE: CC1020: Effect on RF Range of Misaligned Center Frequencies on TX & RX

    Hi RGW, Data rate = 9600 baud, freq dev = 25kHz. With regard to the first equation, Signal BW = Data rate + 2 x frequency deviation , the data sheet says " In both Manchester and NRZ mode, 2 × fm is then equal to the programmed baud rate. " However…

  • CC1020: SmartRF Studio Installation Problems for CC1020 Transceivers

    Part Number: CC1020 Tool/software: I am trying to install SmartRF Studio v6.13.1.0 to work with CC1020 transceivers but I keep getting a "Chipcon Parallel Port Driver Error - Unable to load the parallel port driver!". Please advise how to update…

  • CC1020: Harmonics reduction in transceiver

    TI Thinks Resolved
    Part Number: CC1020 Other Parts Discussed in Thread: CC1311R3 , CC1101 , CC110L Tool/software: Hi, I am using CC1020 as a transceiver for 433MHz UHF range. While operating it in Tx mode with +8dBm, the 2nd harmonic power level is too high i.e., -15dBc…

  • RE: CC1020: RF Interference Disconnecting Devices

    Hi Diego, Vincent informed me that you were working on reproducing our issue, have you been able to? My ticket with Vincent was closed without any warning, so I'm unable to communicate with him anymore.

  • CC1020: RF sensitivity issue

    Part Number: CC1020 Hi. I have designed two CC1020 PCB's for UHF 433 MHz radio communication. One board is used as transmitter & other as receiver. I have configured both in synchronous NRZ mode with 4.8k baud. The receiver is only able to demodulate…

  • RE: CC1020: New batch of CC1020 not working in existing well proven design.

    Hi Dmitry, Are you still having issues with this batch of CC1020? If yes, please take a picture of the marking of the package and any information regarding the source where these were purchased.

  • CC1020: Methods of Greater Resolution for Frequency Programming of the CC1020

    Part Number: CC1020 This post will contain information regarding Section 5.8 Frequency Programming on the CC1020 Datasheet. We are in the process of tuning our RF system to be as close to the center frequency as possible using the center frequency equation…

  • CC1020: Power down mode current consumption variations

    TI Thinks Resolved
    Part Number: CC1020 Hi, We are currently seeing larger variations in production testing measurements on the CC1020 power down mode in our design, some parts show 0.4uA power down current instead of 0.2uA as the historical norm. We have run this part for…
1 2 3 4 5 »

Didn't find what you are looking for? Post a new question.